Martin ATOMIC 3000 Instrukcja Użytkownika Pobierz pdf (Strona 20)

20 Controles remotos Manual do Usuário do Atomic 3000

Ocontroleremotoéalimentadoporumaparelho"master"por

meiodaconexãodedados.OaparelhomasterdoDetonator

é selecionado pela definição dos pinos 2 e 3 do interruptor do

ModoDIPparaON.Utilizeestaconfiguraçãoparaoperarum

únicoaparelhocomocontroleremoto. Se vários aparelhos

forem conectados, defina apenas um para ser o master.

SeoDetonatorestiverconectadoaváriosaparelhos,todos

eles, exceto o master, deverão ser definidos como aparelhos

escravos,comopino2dointerruptordoModoDIPcomoON

edopino3comoOFF.

OPERAÇÃO

INTENSIDADE

Aintensidadedoflashécontroladademínima(apagão)paramáximacomoapagador

gradual de intensidade.

Aintensidademáximaéreduzidanomododeenergiabaixa,queéselecionadonopino

6dointerruptordoModoDIP.

TAXA DO FLASH

A taxa do flash é controlada de 0 a 25 flashes por segundo em fornecimentos de energia

de50Hzoude0a30flashesporsegundoemfornecimentosdeenergiade60Hz,com

o apagador gradual da taxa de flash.

O botão de Execução/Interrupção alterna flashes contínuos como conectados e

desconectados. O diodo indicador fica verde quando estiver em execução e vermelho

quando for interrompido.

ACOMPANHAMENTO/SINCRONISMO

ObotãoAcompanhamento/Sincronismoalternaentreflashesbalanceadosesimultâneos

deváriosaparelhos.OLED indicadorpiscanomododeacompanhamentoepermanece

conectado no modo de sincronismo.

EFEITO OFUSCANTE

O efeito ofuscante é controlado pelo botão momentâneo de Efeito Ofuscante.

A intensidade é controlada com o apagador gradual de intensidade. A alimentação da

lâmpada é regulada eletronicamente para impedir que ela superaqueça.

FLASH ÚNICO

FlashesúnicospodemserconseguidosaopressionarobotãodeFlashÚnicocomoflash

contínuo interrompido.

O ciclo da taxa de flash pode ser reiniciado, por exemplo, para sincronizar com uma

batida,aopressionarobotãodeFlashÚnicoenquantooflashcontínuoestáemexecução.

Configuração do

modo master do

Detonador

Configuração do

modo escravo

do Detonator

20 Remote controls Atomic 3000 user manual

The remote control is powered by a “master” fixture via

the data connection. The Detonator master fixture is

selected by setting pins 2 and 3 of the Mode DIP switch

to ON. Use this setting to operate a single fixture with

the remote control. If multiple fixtures are connected,

set only one to be the master.

If the Detonator is connected to multiple fixtures, all

fixtures except the master shall be set as slave fixtures,

with pin 2 of the Mode DIP switch ON and pin 3 OFF.

OPERATION

I NTENSITY

Flash intensity is controlled from minimum (blackout) to maximum with the

Intensity fader.

The maximum intensity is reduced in low power mode, which is selected on pin 6

of the Mode DIP switch.

F LASH RATE

Flash rate is controlled from 0 to 25 flashes per second on 50 Hz power supplies,

or 0 to 30 flashes per second on 60 Hz power supplies, with the flash rate fader.

The Run/Stop button toggles continuous flashing on and off. The indicator diode

is green when running and red when stopped.

C HASE/SYNC

The Chase/Sync button toggles between staggered and simultaneous flashing of

multiple fixtures. The indicator diode blinks in chase mode and remains on in

Sync mode.

B LINDER EFFECT

The blinder effect is controlled with the momentary Blinder Effect button. The

intensity is controlled with the Intensity fader. Lamp power is electronically

regulated to prevent the lamp from overheating.

S INGLE FLASH

Single flashes can be achieved by pressing the Single Flash button with

continuous flash stopped.

The flash rate cycle can be restarted, for example to synchronize with a beat, by

pressing the Single Flash button while continuous flash is running.

2 3 4 5

Detonator master

mode setting

2 3 4 516

Detonator slave

mode setting

20 Remote controls Atomic 3000 user manual

The remote control is powered by a “master” fixture via

the data connection. The Detonator master fixture is

selected by setting pins 2 and 3 of the Mode DIP switch

to ON. Use this setting to operate a single fixture with

the remote control. If multiple fixtures are connected,

set only one to be the master.

If the Detonator is connected to multiple fixtures, all

fixtures except the master shall be set as slave fixtures,

with pin 2 of the Mode DIP switch ON and pin 3 OFF.

OPERATION

I NTENSITY

Flash intensity is controlled from minimum (blackout) to maximum with the

Intensity fader.

The maximum intensity is reduced in low power mode, which is selected on pin 6

of the Mode DIP switch.

F LASH RATE

Flash rate is controlled from 0 to 25 flashes per second on 50 Hz power supplies,

or 0 to 30 flashes per second on 60 Hz power supplies, with the flash rate fader.

The Run/Stop button toggles continuous flashing on and off. The indicator diode

is green when running and red when stopped.

C HASE/SYNC

The Chase/Sync button toggles between staggered and simultaneous flashing of

multiple fixtures. The indicator diode blinks in chase mode and remains on in

Sync mode.

B LINDER EFFECT

The blinder effect is controlled with the momentary Blinder Effect button. The

intensity is controlled with the Intensity fader. Lamp power is electronically

regulated to prevent the lamp from overheating.

S INGLE FLASH

Single flashes can be achieved by pressing the Single Flash button with

continuous flash stopped.

The flash rate cycle can be restarted, for example to synchronize with a beat, by

pressing the Single Flash button while continuous flash is running.

2 3 4 516

Detonator master

mode setting

2 3 4 5

Detonator slave

mode setting

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Komentarze do niniejszej Instrukcji

Brak uwag

Martin ATOMIC 3000 Instrukcja Użytkownika Strona 20

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Kontrolery DJ Martin ATOMIC 3000