Martin ATOMIC 3000 Instrukcja Użytkownika Pobierz pdf (Strona 12)

12 Funcionamento do controlador Manual do Usuário do Atomic 3000

mod o s d e C o n t Role dmx

AsopçõesdecontroleDMXsãoselecionadasnointerruptor

deModoDIP.

OmodoDMXde1canalpermiteestroboscópioapartirde

0flashesporsegundoatéataxamáximadeflasheseacione

o efeito ofuscante a partir do controle. Para selecionar a

operaçãoDMXde1canal,definaointerruptordopino5do

ModoDIPparaON(conectado);definaospinos1a4para

OFF(desconectado).

OmodoDMXde3canaisfornececontroledeintensidade

de flash, duração de flash e taxa de flash para controle

maisavançado doqueomodode 1 canal.Paraselecionar

a operação DMX de 3 canais, defina os pinos 1 a 5 do

interruptordoModoDIPparaOFF(desconectado).

O modo DMX de 4 canais oferece seis efeitos especiais,

alémdeintensidade,duraçãoecontroledetaxaseflash.Para

selecionarestaoperaçãoDMXde4canais,definaospinos1,

2,3e5paraOFF;definaopino4paraON.

End e R e ç o d e C o ntR o l e

O endereço de controle, também conhecido como canal inicial, é o primeiro canal

utilizado para receber instruções a partir do controlador. O endereço pode ser

qualquercanalde1a511eédefinidonointerruptorDIPdeEndereço.

O Atomic 3000 utiliza 1, 3 ou 4 canais, dependendo do modo de controle.

Para controle independente, cada aparelho deve receber seu próprio endereço

e canais de controle sem sobreposição. Dois ou mais Atomic 3000 podem

compartilharomesmoendereçosenãofornecessáriocontroleindividual.

Para definir o endereço DMX

1.Selecioneumendereçoparaoaparelhoemseucontrolador.Procureaconfiguração

dointerruptorDIPparaoendereçonatabelaabaixo.

2. Definaospinos1a9paraON(conectado)(1)ouOFF(desconectado)(0)conforme

listadonatabela.Definaopino10paraOFF.

Definição de modo

DMX para 1 canal

Definição de modo

DMX para 3 canais

Definição de modo

DMX para 4 canais

12 Controller operation Atomic 3000 user manual

DMX CONTROL MODES

The DMX control options are selected on the Mode DIP switch.

1-channel DMX mode allows you to strobe from 0

flashes per second to the maximum flash rate and trigger

the blinder effect from the controller. To select 1-

channel DMX operation, set pin 5 of the Mode DIP

switch to on; set pins 1 to 4 to off.

3-channel DMX mode provides control of flash

intensity, flash duration, and flash rate for more

advanced control than 1-channel mode. To select 3-

channel DMX operation, set pins 1 to 5 of the Mode DIP

switch to off.

4-channel DMX mode provides six special effects in

addition to flash intensity, duration, and rate control. To

select this 4-channel DMX operation, set pins 1, 2, 3,

and 5 to off; set pin 4 to on.

C ONTROL ADDRESS

The control address, also known as the start channel, is the first channel used to

receive instructions from the controller. The address may be any channel from 1

to 511 and is set on the Address DIP switch.

The Atomic 3000 uses 1, 3, or 4 channels depending on the control mode. For

independent control, each fixture must be assigned its own address and non-

overlapping control channels. Two or more Atomic 3000s may share the same

address if individual control is not required.

To set the DMX address

1. Select an address for the fixture on your controller. Look up the DIP switch setting

for the address in the table below.

2. Set pins 1 through 9 ON (1) or OFF (0) as listed in the table. Set pin 10 to OFF.

2 3 4 5

1-channel DMX

mode setting

2 3 4 516

3-channel DMX

mode setting

2 3 4 516

4-channel DMX

mode setting

12 Controller operation Atomic 3000 user manual

DMX CONTROL MODES

The DMX control options are selected on the Mode DIP switch.

1-channel DMX mode allows you to strobe from 0

flashes per second to the maximum flash rate and trigger

the blinder effect from the controller. To select 1-

channel DMX operation, set pin 5 of the Mode DIP

switch to on; set pins 1 to 4 to off.

3-channel DMX mode provides control of flash

intensity, flash duration, and flash rate for more

advanced control than 1-channel mode. To select 3-

channel DMX operation, set pins 1 to 5 of the Mode DIP

switch to off.

4-channel DMX mode provides six special effects in

addition to flash intensity, duration, and rate control. To

select this 4-channel DMX operation, set pins 1, 2, 3,

and 5 to off; set pin 4 to on.

C ONTROL ADDRESS

The control address, also known as the start channel, is the first channel used to

receive instructions from the controller. The address may be any channel from 1

to 511 and is set on the Address DIP switch.

The Atomic 3000 uses 1, 3, or 4 channels depending on the control mode. For

independent control, each fixture must be assigned its own address and non-

overlapping control channels. Two or more Atomic 3000s may share the same

address if individual control is not required.

To set the DMX address

1. Select an address for the fixture on your controller. Look up the DIP switch setting

for the address in the table below.

2. Set pins 1 through 9 ON (1) or OFF (0) as listed in the table. Set pin 10 to OFF.

2 3 4 516

1-channel DMX

mode setting

2 3 4 516

3-channel DMX

mode setting

2 3 4 516

4-channel DMX

mode setting

12 Controller operation Atomic 3000 user manual

DMX CONTROL MODES

The DMX control options are selected on the Mode DIP switch.

1-channel DMX mode allows you to strobe from 0

flashes per second to the maximum flash rate and trigger

the blinder effect from the controller. To select 1-

channel DMX operation, set pin 5 of the Mode DIP

switch to on; set pins 1 to 4 to off.

3-channel DMX mode provides control of flash

intensity, flash duration, and flash rate for more

advanced control than 1-channel mode. To select 3-

channel DMX operation, set pins 1 to 5 of the Mode DIP

switch to off.

4-channel DMX mode provides six special effects in

addition to flash intensity, duration, and rate control. To

select this 4-channel DMX operation, set pins 1, 2, 3,

and 5 to off; set pin 4 to on.

C ONTROL ADDRESS

The control address, also known as the start channel, is the first channel used to

receive instructions from the controller. The address may be any channel from 1

to 511 and is set on the Address DIP switch.

The Atomic 3000 uses 1, 3, or 4 channels depending on the control mode. For

independent control, each fixture must be assigned its own address and non-

overlapping control channels. Two or more Atomic 3000s may share the same

address if individual control is not required.

To set the DMX address

1. Select an address for the fixture on your controller. Look up the DIP switch setting

for the address in the table below.

2. Set pins 1 through 9 ON (1) or OFF (0) as listed in the table. Set pin 10 to OFF.

2 3 4 516

1-channel DMX

mode setting

2 3 4 516

3-channel DMX

mode setting

2 3 4 5

4-channel DMX

mode setting

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 27 28

Komentarze do niniejszej Instrukcji

Brak uwag

Martin ATOMIC 3000 Instrukcja Użytkownika Strona 12

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Kontrolery DJ Martin ATOMIC 3000