Martin MAC Viper Wash Instrukcja Instalacji

MAC Viper Performance™SAFETY AND INSTALLATION MANUAL

10 MAC Viper Performance Safety and Installation Guide6. See Figure 6. Install a safety wire that is approved as a safety attachment for the weight o

AC power 11AC powerWarning! For protection from electric shock, the fixture must be electrically connected to ground (earth). The AC mains power supp

12 MAC Viper Performance Safety and Installation GuideConnecting to an AC mains power sourceThe MAC Viper Performance power cable can be hard-wired t

DMX data link 13DMX data linkThe MAC Viper Performance has 5-pin locking XLR sockets for DMX and RDM input and output (see Figure 7 on page 12). The

14 MAC Viper Performance Safety and Installation GuideService and maintenanceWarning! Read “Safety Information” on page 4 before servicing the MAC Vi

Service and maintenance 15Lamp lifeMonitor lamp hours using the resettable LAMP ON TIME counter in the INFORMATION control menu. To reduce the risk o

16 MAC Viper Performance Safety and Installation Guide6. Close the lamp access cover and tighten the screw to secure the cover before reapplying powe

Service and maintenance 17Access to the headWarning! Disconnect from power and allow to cool for 30 minutes before opening the head.To open the head:

18 MAC Viper Performance Safety and Installation GuideAccess to the framing moduleBesides the framing effect, the framing module contains the rotatin

Service and maintenance 19CleaningRegular cleaning is very important for fixture life and performance. Buildup of dust, dirt, smoke particles, fog fl

DimensionsAll measurements are given in millimetersThis minimum center-to-center distance can be reduced if pan limits are set via the control menus55

20 MAC Viper Performance Safety and Installation Guide7. Remove the old air filter element from the filter housing and put the new element into posit

Service and maintenance 21LubricationThe MAC Viper Performance does not require lubrication under normal circumstances. The slides for the zoom and f

22 MAC Viper Performance Safety and Installation GuideGobos: generalThe MAC Viper Performance uses specially designed borosilicate 3.3 gobos with a h

Service and maintenance 23Gobo handling and storage1. Store all gobos in a dust-free environment with approx. 50% humidity.2. Always use clean gloves

24 MAC Viper Performance Safety and Installation Guide8. See Figure 22, With a small screwdriver or similar, unhook the end of the gobo spring furthe

Service and maintenance 25edge of the filter up and away from the color wheel slightly to release it, then pull the filter carefully out of its clip

26 MAC Viper Performance Safety and Installation Guide4. See Figure 27. The gobo animation wheel has a magnetic hub with a slot A for the key B in th

Using the fixture 27Using the fixtureBefore using the fixture, download and read the latest version of the MAC Viper Performance User Guide from the

28 MAC Viper Performance Safety and Installation GuideTroubleshooting Problem Probable cause(s) RemedyOne or more of the fixtures is completely dead.

Specifications 29SpecificationsPhysicalLength (base). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ContentsSafety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 MAC Viper Performance Safety and Installation GuideConstructionColor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications 31AccessoriesPower cable, AWG12, SJT, with Neutrik PowerConNAC3FCA input connector, 3 m (9.8 ft.) . . . . . . . . . . . . . . . . . .

Disposing of this productMartin™ products are supplied in compliance with Directive 2012/19/EC of the European Parliament and of the Council of the Eu

www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • DenmarkTel: +45 8740 0000 • Fax +45 8740 0010

Safety InformationThe following symbols are used to identify important safety information on the product and in this document:Warning! The MAC Viper P

Safety Information 5America the cable must be 12 AWG minimum conductor size, SJT or better. In the EU the cable must be 2.5 mm², HAR compliant.• Befo

6 MAC Viper Performance Safety and Installation GuideIntroductionThank you for selecting the Martin™ MAC Viper Performance™. This moving-head spotlig

Introduction 7PackingImportant! Release the tilt lock and allow the fixture to cool before packing it in its flightcase.The anti-shock material in th

8 MAC Viper Performance Safety and Installation GuidePhysical installationWarning! The MAC Viper Performance has a powerful pan motor. The torque rea

Physical installation 9Clamping the fixture on a truss1. Check that the rigging clamps are undamaged and can bear at least 10 times the weight of the